Forrige tråd
Neste tråd
Print tråd
Finneplugg + glassfiber reperasjon
#4485 29/08/2011 1:05 AM
Registrert: May 2011
Innlegg: 4
Nytt medlem
OP Offline
Nytt medlem
Registrert: May 2011
Innlegg: 4

Halloien!

Lurte på om noen vet om ett sted som tar seg av reperasjoner av det kaliber tittelen beskriver? Har vurdert å reparere skaden selv, men kommet frem til at tiden det ville tatt meg er for stor.

Befinner meg i Sogndal, men alle steder sør for Trondheim som tar seg av slikt er aktuelle.

Takker for eventuelle svar...


Re: Finneplugg + glassfiber reperasjon
Bidlibang #4486 16/09/2011 10:54 AM
Registrert: May 2011
Innlegg: 3
Nytt medlem
Offline
Nytt medlem
Registrert: May 2011
Innlegg: 3

Eg befinner meg og i Sogndal, eg trur dei fikser det meste på stadsurf i hoddevik, eg har eit brett til reperasjon der, men dei brukar dritlang tid. Dei sa dei skulle fikse det på 3 dagar, men no har det gått 2 månadar.


Re: Finneplugg + glassfiber reperasjon
Bidlibang #4487 20/09/2011 11:37 AM
Registrert: Aug 2011
Innlegg: 1
Nytt medlem
Offline
Nytt medlem
Registrert: Aug 2011
Innlegg: 1

Bestill dette: http://store.magicseaweed.com/FCS-Plug-Repair-Kit/Item/118/

Og så følger du denne: FCS plug repair

The Fin Control System® by Gorilla Grip® is designed with safety in mind, in most cases a collision between your surfboard and body can result in damage to your surfboard and sometimes injury to yourself.

Using the Fin Control System the chances of this happening are reduced. The fin has tabs that are engineered to break off in most collisions, therefore, causing no damage to the surfboard and reducing the chances of injury.

If this occurs, undo grub screws, turn the surfboard upside down and lightly tap over the broken fin ? the tabs will fall out ? (a freeing agent can be used), then simply replace the fin and go surfing!

If, however, there is damage to your Fin Control Plug in the surfboard, follow these steps.

Gather your materials and tools: 1 1/8?(30mm) holesaw, drill, resin and hardener,fiberglass powder,replacement FCS plug, repair jig (this can be made out of a 2?x4? piece of 1/2? plywood), spare FCS fin,and tape.?Make repair jig by drilling 1 1/8? hole through the center of the 1/2? plywood. This will be used to keep the hole saw straight while drilling out the damaged plug.?Center and tape fin jig over damaged Fin Control Plug. (Picture #1, Jig is aluminum)?Mark hole saw with tape to measure 3/4 inch deep. Drill with hole saw to correct depth, (hole saw should be cutting resin around the Fin Control Plug). (Picture #2)?Remove hole saw and drilling jig, then with a screwdriver in the Fin Control Plug slot, wiggle the plug until it cracks away from the resin and then remove. (Picture #3) ?Install the new Fin Control Plug on the tab of a fin and tighten. (Don?t forget to clean the plugs with acetone before installation). Insert into hole and second plug. Make sure the plug stoppers are flush with the bottom of the board. ?If repair hole is very large, first fill cavity with Q-CELL/resin and sand flat. Note: Do not let Q-CELL/resin set for a long time before refitting the Fin Control Plug. This will ensure that the boring of the hole with Q-CELL/resin is not to difficult.?Tape off area around the plug.?Mix up a enough resin to fill in around the plug. Add some milled or chopped fiberglass to the resin along with hardener. (Do not use Q-CELL filler for this ? it?s too weak.) Using a squeeze bottle or small pouring cup, add the resin into the area around the plug. (Make sure not to drip any resin into the top of the plug.) ?Let the plug harden and then remove the spare fin jig. Turn the screw so it is below the surface of the plug and begin sanding. Use 60 -80 grit to take down the rough part then continue with finer grits.

Repair cracks around Fin Control Plugs in the same manner, but if the crack is very small, scratch up with a sharp instrument and fill with Q-CELL/resin.

Som du sikkert ser så trenger du å kjøpe en hullsag (borre nytt hull til pluggen) som er litt større enn pluggen, samt resin og hardener som du får kjøpt på en butikk som selger ting å fikse båter med f.eks.

Jeg har gjort dette selv, og det funket bra så lenge man er litt nøyaktig, har tålmodighet og har det verktøyet man trenger. I tillegg har man som regel strekene som shaperen har tegnet opp for å finne vinkelen. Det er viktig å putte finnen på de nye (eller gamle) pluggene, slik at avstanden og vinkelen blir korrekt. Pass da på at det ikke kommer noe borti selve finnen sånn at den sitter fast i pluggene (for alltid).

Dette er bedre enn å vente dritlenge på at noen andre skal fikse det, dessuten har du lært deg det til neste gang smile

Lykke til!


Re: Finneplugg + glassfiber reperasjon
Bidlibang #4488 24/09/2011 8:15 PM
Registrert: May 2011
Innlegg: 4
Nytt medlem
OP Offline
Nytt medlem
Registrert: May 2011
Innlegg: 4

Takk for svar!



Fri Flyt utgis av Fri Flyt AS | Postboks 4767 Nydalen, 0421 Oslo | Tlf: 22 04 46 00
Ansvarlig redaktør: Erlend Sande | Redaktør: Henning Reinton | Nettredaktør: Tore Meirik
Salgssjef Fri Flyt AS: Alexander Hagen | Salgskonsulent: Magnus Utkilen | Prosjektleder: Lisa Kvålshaugen Bjærum
Daglig leder: Audun Holmøy Røhrt | Nettsiden er utviklet av Fri Flyt Byrå